VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit container load — brief
starter vape kits · former smokers

Starter Vape Kit container load — brief

Starter Vape Kit is a specification decision before it is a price decision. Get the resistance, the capacity and the packaging right and the price conversation becomes short. Get them wrong and no discount will rescue the order.

Published 01 June 2025  ·  VapeWholesaleHub  ·  Reading time 9 min

Finish and assembly detail checked against the approved reference sample.
Finish and assembly detail checked against the approved reference sample.
Surface finish under raking light, one of the cosmetic checks.
Surface finish under raking light, one of the cosmetic checks.

Assortment planning without the guesswork

We work with former smokers who order between a few hundred and a few thousand units at a time, and we treat both ends the same way: a written specification, a sample you approve, and a production run that matches the sample.

Most former smokers arrive with a spreadsheet and leave with too many SKUs. The fix is not a bigger catalogue, it is a narrower core. We normally propose three tiers: a volume line that carries the shelf, a step-up line that lifts basket value, and one trial SKU that tells you what to order next season.

A practical starting order for former smokers is 120 units across two or three SKUs, not 120 units of one. That spreads the risk, gives your staff something to compare, and still hits the first price break.

Labels, closures and traceability

Labels are where good orders go wrong. Nicotine warnings, child-resistant closures, batch coding and market-specific text all have to be correct before the pallet leaves. We prepare test reports, declaration of conformity and safety data sheets for each shipment and we ask for your destination list early so artwork matches the market.

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

For former smokers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

What happens when something goes wrong

Returns are handled as data, not as complaints. Every reported failure is logged by mode and by batch, and the pattern is reviewed monthly with the factory.

The replacement policy is deliberately simple: report within seven days of delivery with photos and the batch code, and we replace or credit at the next shipment. We do not argue about a defect we can see in a photograph.

  • Document pack prepared per destination market
  • Private label files archived for future rebrands
  • Cartons drop-tested and pallet-counted for clean freight
  • Standing reorder schedule with a fixed cut-off
  • Mixed SKU cartons to spread first-order risk
  • Batch codes traceable from carton back to production date

Shipping without surprises

For repeat buyers we hold a shipping schedule rather than shipping on request. A fixed weekly cut-off means your reorder lands before the shelf empties instead of after.

Transit times move with the season. Book space early for Q4 and around Chinese New Year, when factory output pauses for two to three weeks and freight rates tighten at the same time.

Specification summary

Typical specification for this category
Battery500 mAh
Pod capacity3.0 ml
Coil resistance1.2 ohm
IncludedDevice, 2 pods, cable
ChargingUSB-C 5V/1A
PackagingBlister pack
Minimum order200 units per SKU, mixed cartons allowed
Lead time18 working days after artwork approval

If any of this is unclear, the fastest route is a message rather than a meeting. Send the market you sell into and the price band you work in, and you will get a specific answer instead of a brochure.

Frequently asked

What happens if part of the order is defective?

Report within seven days with photos and the batch code. Confirmed defects are replaced or credited on the next shipment. The failure is logged by mode and batch, and reviewed monthly with the factory.

Can you ship to multiple locations?

Yes. Split shipments are quoted separately because consolidation and splitting price differently. Tell us the destination list at quotation stage and we will show both options.

How do you handle repeat orders?

The specification is held on file against your account, so a reorder is a reference rather than a new brief. We recommend a standing schedule with a fixed weekly cut-off so stock lands before the shelf empties.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us