VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit pallet and container load — a playbook
starter vape kits · former smokers

Starter Vape Kit pallet and container load — a playbook

We ship starter vape kits to distributors, chain buyers and independent shops. What follows is the material we normally cover in a first conversation: what we hold in stock, how we test it, how it ships, and what happens when a carton arrives damaged.

Published 19 September 2026  ·  VapeWholesaleHub  ·  Reading time 5 min

Close inspection of the assembly line before the batch is released.
Close inspection of the assembly line before the batch is released.
Surface finish under raking light, one of the cosmetic checks.
Surface finish under raking light, one of the cosmetic checks.

Price breaks and payment terms

Starter Vape Kit sits in a crowded price band, and the cheapest quote on the sheet is rarely the cheapest unit on your shelf. Everything below is built around reorder rate, defect rate and cash conversion rather than headline unit price.

Payment terms for new accounts are normally a deposit with the balance against the bill of lading. Established buyers on a repeat schedule can move to terms after three clean shipments.

Currency moves more than most buyers expect over a twelve month supply plan. We quote in USD and hold the price for 30 days from confirmation so your margin calculation is not guesswork.

Lead times, freight and landed cost

We ship from Shenzhen and Guangzhou: air express for samples and part loads, sea freight for volume. Typical production lead time is 12 working days after artwork approval, plus transit. We quote both routes so you can see the trade-off instead of guessing at it.

Transit times move with the season. Book space early for Q4 and around Chinese New Year, when factory output pauses for two to three weeks and freight rates tighten at the same time.

For former smokers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Paperwork, labelling and market rules

Regulation for starter vape kits differs by country and sometimes by state. We do not pretend to be your lawyer, but we do keep the document pack current and we will tell you when a configuration cannot legally enter a market you have named.

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

  • Private label files archived for future rebrands
  • Cartons drop-tested and pallet-counted for clean freight
  • Document pack prepared per destination market
  • Batch codes traceable from carton back to production date
  • Standing reorder schedule with a fixed cut-off
  • Mixed SKU cartons to spread first-order risk

What we test before a carton is sealed

We photograph the packing station during production for volume orders. It is a small thing, but it settles most arguments about what was actually in the carton before it was sealed.

12 separate checks run before a carton is sealed: electrical, mechanical, leak, finish and packaging. Anything outside tolerance is quarantined the same day and reported to you, rather than shipped with a hope and a discount.

Specification summary

Typical specification for this category
Battery500 mAh
Pod capacity2.5 ml
Coil resistance1.2 ohm
IncludedDevice, pod, cable
ChargingUSB-C 5V/1A
PackagingBlister pack
Minimum order200 units per SKU, mixed cartons allowed
Lead time30 working days after artwork approval

None of this is complicated. It is just written down, which is more than most buyers get before they wire a deposit.

Frequently asked

Can you ship to multiple locations?

Yes. Split shipments are quoted separately because consolidation and splitting price differently. Tell us the destination list at quotation stage and we will show both options.

What is the minimum order for starter vape kit?

Standard configurations start at 60 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 240 units because of setup time on the line.

How long does production take?

Around 12 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us